Thursday, December 12, 2024

STK435 primarily based Stereo Amplifier Circuit and PCB Design


– Commercial –

efy test

This stereo AF amplifier makes use of the STK435 IC, a extremely well-liked selection because of its simplicity. The STK435, with its 15-pin configuration, requires just a few exterior parts, corresponding to electrolytic and ceramic capacitors and resistors.

With a 12V DC energy provide, the amplifier delivers roughly 7 watts to an 8-ohm speaker, providing glorious audio high quality. The writer’s prototype is proven in Fig. 1.

Elements Record
Semiconductor:
IC1 (IC1A, IC1B): 15-pin STK435 stereo amplifier IC
Resistors (All 1/4-watt, ±5% Carbon)
R1, R15: 1 kΩ
R2, R12, R4, R14: 220 kΩ
R3, R13: 390 kΩ
R5: 100 Ω
R6, R11: 120 Ω
R7, R9: 4.7 Ω
R8, R10: 12 kΩ
Capacitors
C1, C13: 470 pF ceramic disk
C2, C12: 0.47 µF, 25V electrolytic
C3, C11: 10 µF, 25V electrolytic
C4, C9: 220 µF, 25V electrolytic
C5, C10: 47 µF, 25V electrolytic
C6, C7: 1000 µF, 25V electrolytic
C8, C14: 0.1 µF ceramic disk
C15: 100 µF, 25V electrolytic
Miscellaneous
CON1-CON3: 2-pin connectors
LS1, LS2: 8-ohm, 7-watt audio system with 2-pin connectors
Board: 7 cm x 9 cm Veroboard
Energy Supply: 12V battery
Warmth Sink: For IC STK435
STK435 primarily based Stereo Amplifier Circuit and PCB Design
Fig. 1: Stereo AF Amplifier with STK435 IC

Additionally Examine: Stereo AF Amplifier Utilizing TDA1517

– Commercial –

Stereo AF Amplifier – Circuit and Working

The circuit diagram of the STK435-based stereo amplifier is proven in Fig. 2. The design consists of the STK IC, resistors, and capacitors, with two audio inputs and corresponding amplified outputs for the precise and left channels.

Begin by finishing the connections for the primary amplifier part of IC1, known as IC1A. Pin 1 connects to 2 resistors (R2 and R3) in sequence, adopted by a 100-ohm resistor (R5) resulting in the +12V provide. A 10µF, 25V electrolytic capacitor (C3) is related between the junction of R2 and R3 and the bottom. A 0.47µF, 25V electrolytic capacitor (C2) connects to pin 1 of IC1, with its unfavourable terminal linked to a 1-kilo-ohm resistor (R1). Moreover, a 470pF ceramic capacitor (C1) connects the unfavourable terminal of C2 to floor.

Pin 2 connects to the bottom via an electrolytic capacitor of 220µF, 25V (C4) in sequence with a 120-ohm resistor (R6). Pins 3, 4, and eight are additionally grounded. The output from pin 5 drives an 8-ohm, 7-watt speaker (LS1) by way of a 1000µF, 25V electrolytic capacitor (C6). The unfavourable polarity of C6 connects to floor via a sequence association of a 0.1µF capacitor (C14) and a 4.7-ohm resistor (R7).

Pin 6 connects to pin 5 via a 47µF, 25V electrolytic capacitor (C5). Pin 7 is related to the +12V provide, whereas pin 9 connects to +12V via a 100-ohm resistor (R5). A 12-kilo-ohm resistor (R8) bridges pins 2 and 5. A 100µF, 25V electrolytic capacitor (C15) connects pin 9 to floor.

The second amplifier part, IC1B, makes use of pins 10 via 15 and is related as proven in Fig. 2.

Circuit Diagram for Stereo AF Amplifier
Fig. 2: Circuit Diagram

This circuit operates merely: join audio inputs (from gadgets corresponding to laptops, desktops, or MP3 gamers) to CON1 and CON3, then join a 12V energy provide. The amplified output will likely be heard via the audio system.

Additionally Examine: Low-Value Stereo Audio Amplifier Circuit Underneath 50 Rupees

Development and Testing

An actual-size single-sided PCB format for the STK435 amplifier is proven in Fig. 3, with the element format in Fig. 4. After assembling the circuit on the PCB, enclose it in an appropriate cupboard, making certain correct warmth dissipation for the IC with an acceptable heatsink.

Stereo AF Amplifier PCB
PCB design for Stereo AF Amplifier

Alternatively, a 7cm x 9cm Veroboard can be utilized. Place a 15-pin feminine connector in the course of the board, two 2-pin connectors on the far proper and left sides, and a 4-pin connector on the backside. Solder all parts as indicated within the circuit diagram, utilizing a low-watt soldering iron. The IC needs to be inserted after soldering. Join two 8-ohm, 7-watt audio system to the 2-pin connectors, and provide energy utilizing a 12V battery. A clicking sound from the audio system could point out correct connection.

After assembling on both the PCB or a Veroboard, the machine is prepared for testing. Gently contact a steel screwdriver to the 2-pin connectors to listen to a buzzing sound from the audio system, confirming performance. As soon as examined, join an MP3 participant, laptop computer, or desktop to the amplifier’s enter and benefit from the audio output.


Raj Ok. Gorkhali is an electronics hobbyist and a daily contributor to EFY


👇Comply with extra 👇
👉 bdphone.com
👉 ultraactivation.com
👉 trainingreferral.com
👉 shaplafood.com
👉 bangladeshi.assist
👉 www.forexdhaka.com
👉 uncommunication.com
👉 ultra-sim.com
👉 forexdhaka.com
👉 ultrafxfund.com
👉 ultractivation.com
👉 bdphoneonline.com

Related Articles

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Latest Articles